Microsonic zws-15/CD/QS Bedienungsanleitung PDF herunterladen

Sensor adjustment with Teach-in procedure

Set detect point

Place object at position 

Press push-button for about

3 s until LEDs flash

simultaneously

both LEDs:

flash

mutually

Press push-button for

about 1 s

Set window mode

Place object at position 

Press push-button for about

3 s until LEDs flash

simultaneously

both LEDs:

Place object at position ¡

Press push-button for

about 1 s

flash

mutually

Set two way reflective

barrier

Set NOC/NCC

Enable/disable Teach-in

push-button

Switch off power supply

Place object at position 

Press push-button for about

3 s until LEDs flash

simultaneously

Press button for about 13 s

until LEDs flash

mutually

both LEDs:

flash

mutually

Press push-button for

about 10 s

green LED:

yellow LED:

To change output characte-

ristic press push-button

for about 1 s

While pressing the push-

button switch on power

supply

Keep push-button pressed

for about 3 s until both

LEDs flash simultaneously

flashes

on: NOC

off: NCC

green LED:

yellow LED:

flashes

on: push-button

enabled

off: push-button

disabled

To enable/disable Teach-in

press push-button

for about 1 s

Reset to factory setting

Switch off power supply

While pressing the push-

button switch on power

supply

Keep push-button pressed

for about 13 s until both

LEDs stop

flashing

Normal operating mode

Wait for 10 s

Normal operating mode

Operating Instructions

zws-15/CD/QS zws-15/CE/QS

zws-24/CD/QS zws-24/CE/QS

zws-25/CD/QS zws-25/CE/QS

zws-70/CD/QS zws-70/CE/QS

Ultrasonic proximity switch with

one switched output

Product Description

The zws sensor offers a non-contact

measurement of the distance to an

object which must be positioned

Ultrasonic Sensors

within the sensor’s detection zone.

The switched output is set in depen-

dence of the adjusted detect dis-

tance.

Via the push-button, the detect dis-

tance and operating mode can be

adjusted (teach-in). Two LEDs indi-

cate operation and the state of the

switched output.

Safety Notes

 Read the operating instructions

prior to start-up.

 Connection, installation and

adjustment works may only be

carried out by expert personnel.

 No safety component in

accordance with the EU Machine

Directive

Proper use

zws ultrasonic sensors are used for

non-contact detection of objects.

Installation

 Mount the sensor at the installa-

tion site with the aid of the

enclosed mounting plate.

Maximum torque: 0,5 Nm

Fig. 1: Attachment with mounting plate

 Connect a connection cable to the

M8 device plug.

 Avoid mechanical load on the con-

nector.

Fig. 2: Pin assignment with view onto sensor

plug and colour coding of the

microsonic connection cable

Start-Up

 Connect the power supply.

 Carry out the adjustment

in accordance with the diagram.

Factory Setting

 Operation with one detect point

 Switched output on NOC

 Detect points at operating range

colour

-U

brown

blue

Sync

black

white

Operating modes

Three operating modes are available

for the switched output:

 Operation with one detect point

The switched output is set if the ob-

ject falls below the set detect point.

 Window mode

The switched output is set if the ob-

ject is within the set window mar-

gins.

 Two-way reflective barrier

The switched output is set if the ob-

ject is between sensor and reflector.

Synchronization

You can synchronize as many sensors

as you like.

 Apply a square-wave signal to the

sync-input with pulse width t

and

repetition rate t

(Fig.3 and

technical data).

A high level on the sync-input will

deactivate the sensor.

Fig.3: External synchronization signal

Checking operation mode

 In normal mode shortly press the

push-button.

The green LED stops shining for one

second, then it will show the current

operating mode:

1 x flashing = operation with one

switching point

2 x flashing = window mode

3 x flashing = reflective barrier

After a break of 3 s the green LED

shows the output function:

1 x flashing = NOC

2 x flashing = NCC

Maintenance

microsonic sensors are maintenance-

free. In case of excess caked-on dirt

we recommend cleaning the white

sensor surface

Notes

 The zws sensor has a blind zone,

within which distance measure-

ments are not possible.

 In the normal operating mode, an il-

luminated yellow LED signals the

switched output is switched

through.

 The standard sensor has no tempe-

rature compensation.

 If the object to be sensed moves

into the detection area from the

side, the switching distance should

be set 8-10 % further than the de-

sired switch point to obtain a reli-

able object detection.

If the object moves towards the

sensor (e.g. level control) the detect

point can be taught to the actual

distance at which the sensor has to

switch the output.

Sensor disabled Sensor disabled

Start

-U

Set switched output

Further settings

1 2

Ultrasonic Sensors 1

Inhaltsverzeichnis

Seite 1 - Ultrasonic Sensors

Sensor adjustment with Teach-in procedureSet detect pointPlace object at position Press push-button for about3 s until LEDs flash simultaneously both

Seite 2

Technical dataBlind zoneOperating rangeMaximum rangeAngle of beam spread20 mm150 mm50 mm240 mm250 mmSee detection zone350 mmSee detection zoneTransduc

Verwandte Modelle: zws-15/CE/QS | zws-24/CD/QS | zws-24/CE/QS | zws-25/CD/QS | zws-25/CE/QS | zws-70/CD/QS | zws-70/CE/QS |

Kommentare zu diesen Handbüchern

Keine Kommentare

Microsonic zws-15/CD/QS Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Microsonic zws-15/CD/QS herunter. Microsonic zws-15/CD/QS User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: zws-15/CE/QS | zws-24/CD/QS | zws-24/CE/QS | zws-25/CD/QS | zws-25/CE/QS | zws-70/CD/QS | zws-70/CE/QS |

Kommentare zu diesen Handbüchern