Microsonic sks-15/CI Bedienungsanleitung PDF herunterladen

Sensor adjustment with Teach-in procedure

Set window margins

Place object at position ➀

Press push-button for about 3 s until LEDs

flash

simultaneously

both LEDs:

Place object at position ➁

Set rising/falling output

characteristic curve

Press button for about 13 s until LEDs

flash

mutually

flash

mutually

green LED:

yellow LED:

flashes

on: rising

off: falling

characteristic curve

Enable/disable Teach-in push-

button

Switch off power supply

Reset to factory setting

Switch off power supply

While pressing the push-button

switch on power supply

Keep push-button pressed for

about 3 s until both LEDs flash

simultaneously

green LED:

yellow LED:

flashes

on: push-button

enabled

off: push-button

disabled

While pressing the push-button

switch on power supply

Keep push-button pressed for

about 13 s until both LEDs stop

flashing

Press push-button for

about 1 s

Normal operating mode

To change output characteristic press

push-button for about 1 s

Wait for 10 s

To enable/disable Teach-in press

push-button

for about 1 s

Wait for 10 s

Normal operating mode

Operating Instructions

sks-15/CI

sks-15/CU

Ultrasonic proximity switch with

one analogue output

Ultrasonic Sensors

Product Description

The sks sensor offers a non-contact

measurement of the distance to an

object which must be positioned

within the sensor’s detection zone.

Depending on the set window limits,

a distance-proportional analogue sig-

nal is output.

Via the push-button, the detect dis-

tance and operating mode can be

adjusted (teach-in). Two LEDs indi-

cate operation and the state of the

output.

Safety Notes

■ Read the operating instructions

prior to start-up.

■ Connection, installation and

adjustment works may only be

carried out by expert personnel.

■ No safety component in

accordance with the EU Machine

Directive.

Proper Use

sks ultrasonic sensors are used for

non-contact detection of objects.

Installation

■ Mount the sensor at the installa-

tion site.

Maximum torque of screws:

0,5 Nm

■ Connect a connection cable to the

M8 device plug.

Fig. 1: Pin assignment with view onto sensor

plug and colour coding of the

microsonic connection cable

Start-Up

■ Connect the power supply.

■ Carry out the adjustment in

accordance with the diagram.

Factory Setting

■ Rising analogue characteristic

curve between the blind zone and

the operating range.

colour

-U

brown

blue

Com

black

white

Synchronization

If several sensors are mounted close

to another, they should be synchroni-

zed with each other. This is done by

an externally provided synchronisati-

on signal.

■ Apply a square-wave signal to the

sync-input with pulse width t

and

repetition rate t

(Fig. 3 and

technical data).

Any amount of sensors may be syn-

chronized with this external synchro-

nisation signal.

A high level on the sync-input will

deactivate the sensor.

Fig. 3: External synchronization signal

Maintenance

microsonic sensors are maintenance-

free. In case of excess caked-on dirt

we recommend cleaning the white

sensor surface.

Notes

■ The sks sensor uses an internal

temperature sensing element to

compensate the temperature de-

pending speed of sound. In the

first 45 seconds after power on

every time the sks tests this tem-

perature compensation and after-

wards sets the analogue output

according to the compensated dis-

tance value.

■ The temperature compensation

automaticly adjusts to the actual

mounting conditions if the sensor

outputs current of 11 to 13 mA or

voltage of 4.4 to 5.6 V for at least

30 minutes after switching on

power supply.

■ The sks sensor has a blind zone,

within which distance measure-

ments are not possible.

■ In the normal operating mode, an il-

luminated yellow LED signals that the

object is within the adjusted win-

dow limits.

■ If the push-button is not pressed

for 30 seconds during the teach-in

setting, the settings made hitherto

are deleted.

■ The sensor can be reset to its fac-

tory setting (s. »Further settings«).

Sensor disabled Sensor disabled

Start

-U

Set analogue output

Further settings

1 2

Inhaltsverzeichnis

Seite 1 - Ultrasonic Sensors

Sensor adjustment with Teach-in procedureSet window marginsPlace object at position ➀Press push-button for about 3 s until LEDsflash simultaneously bo

Seite 2 - 89/336/EEC

Technical datablind zoneoperating rangemaximum rangeangle of beam spread20 mm150 mm250 mmsee detection zonetransducer frequencyresolution, sampling ra

Verwandte Modelle: sks-15/CU

Kommentare zu diesen Handbüchern

Keine Kommentare

Microsonic sks-15/CI Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Microsonic sks-15/CI herunter. Microsonic sks-15/CI User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: sks-15/CU

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Microsonic sks-15/CI