Microsonic LCA-2 Bedienungsanleitung

EW-DO-021316 Rev. 9-267434 Subject to change without notice *B2204* LINKCONTROL VERSION 7.6 Programming of ultrasonic sensors

Page 10 of 51 Preparation SELECTING THE COM-PORT For the communication of LinkControl with the computer, you have to select the COM-Port. DIRE

Reading / writing parameters Page 11 of 51 READING / WRITING PARAMETERS READING PARAMETERS FROM A CONNECTED SENSOR only for mic-.../M30, lc

Page 12 of 51 Reading / writing parameters READING PARAMETERS FROM A FILE  Click  select, whether you want to load parameters out of a

Reading / writing parameters Page 13 of 51 TRANSMIT PARAMETERS TO THE SENSOR All changes that you have made in the input masks, are only te

Page 14 of 51 Reading / writing parameters CONVERSION OF PARAMETERS FOR THE R1 SENSORS The mic-XX/YY/HV/M30 and lcs-XX/YY/HV/QP ultrasonic senso

Reading / writing parameters Page 15 of 51  Connect an R1 sensor of the same type to the LinkControl adaptor (Ics-25/DD/HV/QP R1 shown in the

Page 16 of 51 Reading / writing parameters If LinkControl was not able to convert all parameters, the software asks you to check the converted pa

Reading / writing parameters Page 17 of 51 SAVING PARAMETERS TO A FILE  Click  Select a file name of your own and confirm by pressing

Page 18 of 51 Changing parameters on distance measuring sensors CHANGING PARAMETERS ON DISTANCE MEASURING SENSORS Depending on the connected

Changing parameters on distance measuring sensors Page 19 of 51 TEMPERATURE COMPENSATION The velocity of sound in air is temperature dependent.

NOTES Page 2 of 51

Page 20 of 51 Changing parameters on distance measuring sensors mm: the measured distance value is indicated in mm and/or cm 0...100%: the meas

Changing parameters on distance measuring sensors Page 21 of 51 ADJUSTMENT OF TEMPERATURE COMPENSATION Only for sensors mic+.../TC, ,mic-...M

Page 22 of 51 Changing parameters on distance measuring sensors SETTING THE SENSOR TO ITS DEFAULTS  Click  Confirm the security query.

Changing parameters on distance measuring sensors Page 23 of 51 CHANGING PARAMETERS FOR SWITCHING SENSORS microsonic ultrasonic sensors with p

Page 24 of 51 Changing parameters on distance measuring sensors Some very interesting applications can be derived from the possibility to load bo

Changing parameters on distance measuring sensors Page 25 of 51 CHANGING PARAMETERS FOR ANALOGUE SENSORS The sensors resolve distances to 0.36

Page 26 of 51 Changing parameters on distance measuring sensors ENDWERTBEGRENZUNG only pico+ You can insert an additional break point behin

Changing parameters on distance measuring sensors Page 27 of 51 FILTER SETTINGS FOR DISTANCE MEASURING SENSORS microsonic brand ultrasonic sens

Page 28 of 51 Changing parameters on distance measuring sensors This filter method simulates an arithmetic mean value calculation over several me

Changing parameters on distance measuring sensors Page 29 of 51 SENSOR FAMILIES MIC-.../M30 UND LCS Within these sensor families you are able

CONTENT Page 3 of 51 Preparation 5 Delivery scope 5 System requirements 5 Installing the Software 6 Connection of the LCA-2 7 Pinning /

Page 30 of 51 Changing parameters on distance measuring sensors AVERAGE – FILTER The filter method average simulates an arithmetic mean value

Changing parameters on distance measuring sensors Page 31 of 51 SENSOR FAMILIES LPC UND UCS Within these sensor families you are able to selec

Page 32 of 51 Parameter change in the double sheet control PARAMETER CHANGE IN THE DOUBLE SHEET CONTROL The function of the double sheet detect

Parameter change in the double sheet control Page 33 of 51 OPERATING MODES You can select from the following operating modes:  Free-Run-Mode

Page 34 of 51 Parameter change in the double sheet control TRIGGER MODE – 2 VORDEFINIERTE MATERIALKLASSEN + 1 TEACH-IN If the dbk+4 is paramete

Parameter change in the double sheet control Page 35 of 51 OUTPUT FUNCTIONS You can make the following settings: Function for switched output D

Page 36 of 51 Parameter change in the double sheet control VOLTAGE LEVEL OF THE LOGIC STATES AT THE CONTROL INPUTS Logical state Voltage level

Parameter change in the Label-/Splice Sensors esp-4 and esf-1 Page 37 of 51 PARAMETER CHANGE IN THE LABEL-/SPLICE SENSORS ESP-4 AND ESF-1 Label

Page 38 of 51 Parameter change in the Label-/Splice Sensors esp-4 and esf-1 TEACH-IN-METHODS The esf-1 can reliably detect high-transparency, re

Parameter change in the web edge sensor bks+ Page 39 of 51 PARAMETER CHANGE IN THE WEB EDGE SENSOR BKS+ The bks+ ultrasonic web edge sensor is

CONTENT Page 4 of 51 Teach-in-Methods 38 A) Learn both backing material and label dynamically 38 B) Separate teach-in for backing material

Page 40 of 51 Parameter change in the web edge sensor bks+ TEACH-IN-METHODEN To adjust the zero position of the edge to be controlled, the senso

Parameter change in the web edge sensor bks+ Page 41 of 51 FILTER SETTING The filter type F can be chosen from 0 to 3. Where is: 0: No Filter 1

Page 42 of 51 Documentation of parameters DOCUMENTATION OF PARAMETERS THE PARAMETER LIST  Click , to get a list of the adjusted parameters

Visualisation of measurements Page 43 of 51 VISUALISATION OF MEASUREMENTS SELECTING THE MODE  Click only for mic-.../M30, lcs and lpc

Page 44 of 51 Visualisation of measurements NUMERIC PRESENTATION The measuring value is displayed in "mm" and as a bar graph in perc

Visualisation of measurements Page 45 of 51 GRAPHIC PRESENTATION The displayed output characteristics correspond to the settings in the input

Page 46 of 51 Visualisation of measurements MEASUREMENT WRITER Every measuring value is displayed time continuous like an x-t writer. The expe

Visualisation of measurements Page 47 of 51 MARKINGS Blindzone, foreground suppression, switching- and hysteresis points (on sensors with switc

Page 48 of 51 Visualisation of measurements LOG MEASUREMENTS For logging, the measurements can be saved into a file.  Push the button Protocol

Individual input mask Page 49 of 51 INDIVIDUAL INPUT MASK LOCKING INPUT FIELDS You can create your own input mask by enabling or disabling ce

Preparation Page 5 of 51 PREPARATION DELIVERY SCOPE The LinkControl Adapter is delivered separately or in a plastic case with the following c

Page 50 of 51 The LinkCopy function THE LINKCOPY FUNCTION LINKCOPY WITH LCA-2 With the LCA-2 you can copy parameters of a sensor onto a second

Updating LinkControl Page 51 of 51 UPDATING LINKCONTROL Link Control is continuously updated. Please take a look at our website and download

Page 6 of 51 Preparation INSTALLING THE SOFTWARE  Start your computer and wait until Windows has booted.  Insert the installation USB stic

Preparation Page 7 of 51 CONNECTION OF THE LCA-2 For further Information see: quick reference guide on the LCA-2

Page 8 of 51 Preparation PINNING / COLOUR CODING For connecting lcs-sensors or mic-sensors with cable to the LinkControl Adapter please use fo

Preparation Page 9 of 51 LAUNCHING THE LINKCONTROL SOFTWARE After starting the software… the start-up screen appears. LinkControl checks, i